Aircraft Worker Resume Samples

An Aircraft Worker works for the aircraft and aviation industry and undertakes the crucial job of repairing and performing regular maintenance on aircraft. The job description entails performing aircraft inspections as needed by the Federal Aviation Administration. Typical duties that are seen listed on the Aircraft Worker Resume are – diagnosing mechanical and electrical problems; repairing wings, brakes, and electrical systems; replacing defective parts using hand tools and power tools; examining replacement aircraft parts for defects; reading maintenance manuals for identifying repairing procedures; testing aircraft parts with gauges and other diagnostic equipment, and inspecting completed work to ensure it aligns with performance standards.

The workers should be above 18 years of age and possess the following skills – mechanical skills and physical strength; dexterity to coordinate the movement of fingers and hands; observational skills, and troubleshooting skills. Almost all workers in this field have a training certificate approved by the aviation maintenance technician school.

Aircraft Worker Resume example

Aircraft Worker Resume

Headline : As an Aircraft Worker, responsible for Removing, cleaning, reinstalling, or replacing defective parts, accessories, and components such as worn gaskets, couplings, and fittings.

Skills : Aircraft, Planning Skills, Mechanical Skills.

Description :

    1. Directed in incoming and outgoing aircraft near the hanger area to assist pilots maneuvering of aircraft on the ground, using hand or light signals.
    2. Secured aircraft in parking position with chocks and tie-down chains.
    3. Replenished fuel, oil, water, waste system chemicals, oxygen, and hydraulic fluid.
    4. Checked for fuel contamination by draining samples from low point drains.
    5. Operated ground support equipment such as electrical power supply, tow tractors, light carts, and engine starting units.
    6. Cleaned exterior or interior of aircraft, using portable platform ladders, brushes, rags, water hose, and vacuum.
    7. Performed all other position related duties as assigned or requested.
Years of Experience
Experience
5-7 Years
Experience Level
Level
Executive
Education
Education
BA In Electrical Engineering


Aircraft Worker Resume

Objective : Highly motivated, experienced, and passionate candidate seeks to further a career in an Aircraft Worker position that can utilize my technical skills and management knowledge to benefit mutual growth and success.

Skills : Soldering Skills, Mechanical Skills, Communication Skills.

Description :

    1. Maintained equipment to keep in working order: hydraulic system & hoses on 4000 TRL, B-4 stands, 3000 TRL, B-1 stand.
    2. Inspected/daily equipment: hydraulic systems hoses on jacks.
    3. Maintained equipment, assembles, and disassembles tire presser 21C loaders.
    4. Inspected & operated 21C knuckles.
    5. Roofed sheet metal maintaining.
    6. Inspected and maintained roofs, gutters, flashing downspouts, skylights.
    7. Supported aircraft operations, maintenance, conducting inspections, diagnosing discrepancies, and repairing hydraulic/pneumatic systems.
Years of Experience
Experience
2-5 Years
Experience Level
Level
Junior
Education
Education
GED


Aircraft Worker Resume

Headline : Excellent problem solver capable of seeing multiple levels of problems and developing effective solutions. Proven middle-level management with experience in the oversight of multiple projects and able to manage all aspects of a department. 

Skills : Microsoft Office, Leadership, Attention To Detail,  Supervision, Team Building.

Description :

    1. Ability to manufacture, fabricate, develop, install, and repair items from high strength, titanium, aluminum, and numerous alloys.
    2. Ability to read and interpret blueprints.
    3. Checked for visible corrosion, distortion, and cracks in the fuselage, wings, and tail.
    4. Conducted routine and special inspections as required by regulations.
    5. Inspected parts such as turbine blades and cylinders for corrosion, wear, warping, cracks, and leaks.
    6. Assisted in towing and jacking aircraft, and disconnecting instruments, ignition systems, and fuel and oil lines.
    7. Prepared and maintained detailed repair, inspection, investigation, and certification records and reports.
Years of Experience
Experience
5-7 Years
Experience Level
Level
Executive
Education
Education
High School Diploma

Aircraft Worker Resume

Objective : Aircraft Worker with 2 years of experience in Obtaining standard parts such as fuel and oil line connections and fittings, cable linkage, and spark plug cables and harnesses by referring to parts manuals and by making comparisons with samples.

Skills : Management Skills, Reading Skills, Communication Skills.

Description :

    1. Utilized the current management information system(s) to maintain aircraft forms and records as required by the customer.
    2. Drafted and submitted aircraft/engine management and Inventory Reporting System reports in a timely manner.
    3. Prepared weekly, monthly, yearly reports as assigned.
    4. Processed readiness documents, administer the aircraft configuration status accounting program, and verify aircraft utilization reports.
    5. Monitored aircraft configuration status, weight and balance, and aircraft inventory data for accuracy.
    6. Initiated and distributed applicable maintenance forms in accordance with established procedures.
    7. Assisted in preparation of the Monthly Maintenance Plan.
              Years of Experience
              Experience
              2-5 Years
              Experience Level
              Level
              Executive
              Education
              Education
              High School Diploma

              Aircraft Worker Resume

              Objective : Aircraft Worker with 5 years of experience in Servicing engines and aircraft components at line station making repairs, short of overhaul, Requiring to keep aircraft in safe operating condition, and also Performing other job-related duties as may be assigned.

              Skills : Mechanical SKills, Supervising Skills, Problem Solving Skills.

              Description :

                1. Typically worked assignments include the disassembly of aircraft or major components for overhaul or modification.
                2. Removed sheet metal parts from aircraft to be reconditioned.
                3. Removed major aircraft components of aircraft structure or systems control surface, doors, hatches, landing gear assemblies, electrical wiring, control cables, etc.
                4. Assisted in configuration changes, refuel/defuel, and towing.
                5. Always remained in compliance with the depots PPE policy and helped bring unsafe practices to the attention of others.
                6. Apply standardized and specific procedures to accomplish tasks of limited complexity.
                7. Performed the full range of duties that encompass the disassembly, repair, rebuild, modification, assembly, and maintenance of parts and subassemblies of hydraulic and pneumatic components.
              Years of Experience
              Experience
              2-5 Years
              Experience Level
              Level
              Junior
              Education
              Education
              GED

              Aircraft Worker Resume

              Headline : Aircraft Worker with 6 years of experience in Performing maintenance and inspection work (on-site and in the shop) on rotary-wing aircraft systems, subsystems, and their components, and also Performing maintenance tasks, coarse and fine alignments, and adjustments on engine fuel controls.

              Skills : Repairing SKills, Analyzing Skills, Supervising Skills.

              Description :

                1. Performed a variety of tasks associated with inducting, cleaning, screening, and identifying, buffing and polishing, lubricating and preserving, and packaging new and used bearings.
                2. Unpackaged and unwrapped bearings, disassemble bearings and remove seals, check identity, login, tag, prepare shop traveler, segregate and place in the basket.
                3. Reworked and damaged seals to restore condition.
                4. Determined cleaning procedure from established procedures appropriate for the type of bearing.
                5. Used vibratory cleaner and/or other equipment in the cleaning line.
                6. Checked identity of bearing and etched identifying information, e.g., part of contract number, FSN, service activity, time, and date data on bearing.
                7. Demagnetized bearings and seals, applied proper type and amount of lubricant, replaces seals, and places in a plastic bag with appropriate preservative.
              Years of Experience
              Experience
              5-7 Years
              Experience Level
              Level
              Management
              Education
              Education
              High School Diploma

              Aircraft Worker Resume

              Objective : As an Aircraft Worker, responsible for monitoring and servicing all aircraft systems for day to day flight schedule support, work maintenance requirement cards in relation to daily and turnaround inspections and operate all ground support equipment.

              Skills : Microsoft Outlook, Training Skills, Creative Skills.

              Description :

                1. Successfully performed the responsibilities of an Aircraft Worker including but not limited to the proper completion of daily and Turnaround inspections of aircraft.
                2. Assisted pilots during flight preparation and advised them of the material condition of the aircraft.
                3. Diligently oversaw the fueling and refueling of aircraft.
                4. Strictly followed written technical documents, as well as oral instructions to perform inspections.
                5. Tactfully resolved technical issues within the department.
                6. Worked independently and ensured safe work practices and good housekeeping while assuring timely tools, equipment, material, and procedure availability.
                7. Trained in all phases of storage services procedures for preservation of aircraft; including preparation of aircraft and application of spray last.
              Years of Experience
              Experience
              2-5 Years
              Experience Level
              Level
              Executive
              Education
              Education
              BS

              Aircraft Worker Resume

              Objective : Highly qualified Aircraft Worker with experience in the industry. Enjoy creative problem solving and getting exposure on multiple projects, and I would excel in the collaborative environment on which your company prides itself.

              Skills : Operating Skills, Mechanical Skills, Creative Skills.

              Description :

                1. Set up and operated packaging, sealing, and labeling equipment  to package and label bearings.
                2. Performed visual, auditory, tactile, and dimensional examination and evaluation of bearings and rebuild bearings.
                3. Performed repairs such as removing and replacing worn or damaged gaskets.
                4. Ability to do the work of an aircraft worker without more than normal supervision.
                5. Performed Quality Assurance on every aircraft that inspected.
                6. Performed launch and recovery evolutions, daily and turnaround inspections between flights, fueling, and preparing aircraft for the daily flight.
                7. Performed pre-flight and post-flight inspections Launch out aircraft with proper hand signals and safety.
              Years of Experience
              Experience
              2-5 Years
              Experience Level
              Level
              Executive
              Education
              Education
              BA

              Aircraft Worker Resume

              Objective : As an Aircraft Worker, responsible for Complying with Foreign Object Damage (FOD), Hazardous Waste Program, and Tool Control Programs, and also Compling with all established general and industrial safety rules and regulations as applicable to the contract, facility, and job assignment.

              Skills : Monitoring Skills, Troubleshoot, Aircraft.

              Description :

                1. Responsible for the launch and recovery of assigned aircraft.
                2. Removed and replaced hydraulic components, flight controls, engines, tires, landing gear, fuel system components, tail hook, and transmissions.
                3. Utilized ground support equipment: NC-8, TA-75, NAN Cart, Hydraulic Jenny, and Hydraulic Servicing Unit, PON-6, aircraft jacks, overhead hoist, engine stand, wing stand, and various aircraft slings.
                4. Utilized various measuring devices including inside and outside micrometers, dial indicators, spline gages, depth gages, multimeters, and tension meters, also PSI, fuel quantity, etc.
                5. Troubleshoot airframe gripes and assist aircraft electricians and power plant mechanics.
                6. Assured all documentation was complete.
                7. Monitored, verified, and logged Support Equipment Custody records, Aviation Armament Equipment, aircraft inventory records, and Technical Directives as applicable.
              Years of Experience
              Experience
              2-5 Years
              Experience Level
              Level
              Executive
              Education
              Education
              High School Diploma

              Aircraft Worker Resume

              Summary : Aircraft Worker with 7 years of experience in Performing duties as Aircraft Worker on P-3 aircraft in support of Customs Border Protection (CBP), Monitoring and servicing all aircraft systems for day to day flight schedule support, work maintenance requirement cards in relation to daily and turnaround inspections and operate all ground support equipment.

              Skills : Mechanical Skills, Reparing Skills, Problem Solving Skills.

              Description :

                1. Performed visual inspections before rigging, adjusting, testing, and operational check of flight controls and mechanical systems.
                2. Removed and Replaced engines, gearboxes, and APU systems.
                3. Helped in performing rigging of flight controls and cable tension using calibrated tools.
                4. Assembled fuel cells and performed fuel cell integrity checks.
                5. Worked duties performed independently, with minimal or no supervision.
                6. Capabled of reading and interpreting blueprints, technical directives, maintenance inspection manuals, and Illustrated Parts Breakdown.
                7. Repaired painted surfaces on aircraft components or repainted masked parts of components not to be painted according to shop manuals and made blueprints.
              Years of Experience
              Experience
              7-10 Years
              Experience Level
              Level
              Management
              Education
              Education
              BS